More Progress

Please share with your friends!

More Progress

Plowden Progress

Purfling and Graduation

While varnish was drying on the Titian model, I went back to the Plowden model, and began purfling the front plate and graduating the back plate:

Graduation about half done.
Graduation about half done. 

 

Graduation progress and purfling installed.
Graduation progress and purfling installed.

 

Also, I finalized the finishing process on the Titian model, and an ready to begin set-up. The pegs are trimmed, polished and drilled for strings. The nut is at the correct level and has been slotted for strings. The saddle is installed, too. The end button and soundpost were both installed quite some time ago. So, really, all that is left is the bridge and strings, and final adjustment. I don’t tend to count the tailpiece, but, as a matter of fact, it, too requires some adjustment. So does the chinrest, so I shouldn’t treat them as non-entities. The feet opf chinrests virtually never fit correctly as shipped. Tailpiece adjustment requires trial and error fitting, to get the ratio between vibrating string length and after-length (string between bridge and tailpiece fret) adjusted to a 6:1 ratio.

Anyway, here is where it currently stands. I could probably finish it tonight, but then I would be too tired to go to work in the morning…so, tomorrow will have to do. 🙂

Titian front, ready for set-up.
Titian front, ready for set-up.

 

Titian back, ready for set-up.
Titian back, ready for set-up.

 

Nut and pegs complete, ready for strings.
Nut and pegs complete, ready for strings.

 

Saddle installed, ready for set-up.
Saddle installed, ready for set-up.

 

So, I hope to take both of these instruments to the show in March (“Violin Tasting Event” at the Hilton Hotel, March 10th in Corvallis, OR), as well as the one in May (which used to be the Marylhurst show, but it will now be at Portland Community College, Sylvania campus: still called the Northwest handmade musical instrument show.) Anyway: lots of work left to do, in order to get ready.

Thanks for looking.

If you found this post helpful, please share with your friends!

More Fiddle Progress

Please share with your friends!

Progress on the Small (14-inch) Viola and the “Plowden” Guarneri model violin

Here are some photos of what is happening with these two fiddles. I decided to add a third instrument to the bench, so to speak, a 3/4-size violin (separate notes on separate thread), so it is slowing me down just a little.

Progress Checklist

Both the viola and the violin are moving along:

  • Arching is complete on the front plates of both instruments.
  • F-holes are laid out on both instruments, cut out and complete on the violin.
  • The bass bar has been fitted, installed and trimmed in the viola.
  • Graduation is nearly complete on the viola, complete on the violin.
  • The scrolls are partially carved…still a fair way to go.
  • The back plates are arched, but there is still some work to be done on each before I would call them absolutely complete.
  • The top plate has been installed on the violin, and purfling installed.
  • The violin top plate and rib garland are nearly complete…the edgework is done, but some refining will still happen.
  • You can see that I trimmed a couple of millimeters off the corners of the violin front plate. I will do the same on the other three plates as well.

Here are some photos:

July 3rd status of Guarneri-model violin.
July 3rd status of Guarneri-model violin. (Wood for back, sides and neck is European Maple. Wood for top is European Spruce.)

 

July 3rd status Guarneri-model violin back
July 3rd status Guarneri-model one-piece violin back. Arching and graduation are nearly complete.

 

July 3rd status of Oliver 14
July 3rd status of Oliver 14″ Viola.

 

July 3rd status Oliver 14 inch Viola front plate
July 3rd status Oliver 14 inch Viola front plate. Arching and graduation essentially complete. F-holes laid out and deeply incised. (Wood is Sitka Spruce.)

 

July 3rd status Oliver 14 inch Viola back plate
July 3rd status Oliver 14 inch Viola back plate. Arching and graduation nearly complete. (Wood is spalted, highly figured Big Leaf Maple, harvested about five miles from my house.)

 

July 3rd status Oliver 14 inch Viola scroll and neck.
July 3rd status Oliver 14 inch Viola scroll and neck. (Wood is spalted Big leaf maple…from the same log as the back plate.)

Prognosis:

So…you can see that progress is happening. Not at a very exciting pace, but I hope the wait will be worthwhile.

My goal is to produce three very good instruments this summer/fall:

  • the 14-inch viola,
  • the Guarneri-model violin, and
  • the 3/4-size violin,

and then show them, along with a larger viola, to orchestra directors and teachers in the Greater Portland Area.

My rationale is that good small violas are hard to find, and so are good fractional sized instruments. If I can demonstrate to the teachers that I can produce very good instruments in smaller sizes, as well as the larger sizes, then perhaps they will recommend their students to me.

All I can do is try….

Thanks for looking.

If you found this post helpful, please share with your friends!