More Progress: The Plowden-model looks like a violin!
Removed the Mold and Installed the Back Linings
One nice thing about this (French-style) mold is that it is easy to remove– it usually takes less than five minutes to get it out, provided I have waxed the non-glued surfaces of the mold, so there is no chance of an accidental adhesion to the ribs. I simply use a flat chisel to crack the glue loose at each block, where it is attached to the mold, and then slip my parting knife (in reality, it is an old potato knife) between the block and the mold, to make sure nothing is still adhering to the mold. After that I can slide the mold out by lifting as shown, while wiggling each individual block to make sure they are all moving evenly. The only drawback is that I have to install the back linings after the mold is removed, and the rib garland is pretty fragile. In the past, I have used a two-part collapsible mold, in the italian style (centered between the front and back edges of the ribs); but it is more difficult to remove. The only real advantage is that I can install all the linings while the corpus is still on the mold, and still get the mold out without too much trouble. I believe it does have a slightly greater tendency to leave the ribs slightly convex in the center, as well, and some people find that attractive. (I do too…. Perhaps I will eventually go back to using the Italian-style molds.)
This time, the linings went in without a struggle, though, and the whole task took about 30-40 minutes. A few hours later, the glue had dried, and I was able to remove all the tiny spring-clamps, and get going on leveling the back of the garland, and cleaning up the interior.
Cleaning up the Interior
Cleaning the interior primarily means shaping the linings and blocks, after the mold is out of the way, but it also is a final opportunity to scrape any rough spots, and make any minuscule repairs. So, I put on my magnifying visor, and look things over very carefully. I use a knife to trim the linings so that they are triangular in cross-section, thickest at the edge, to suport the edge of the rib, but tapered so as to not restrict the vibrations of the middle of the ribs too much.
One thing I have to remember, at this point, is that it is also my “last shot” at the interior of the back plate, so, before I install it, I carefully check and scrape it, and, as a final “seal of approval”, I install my signed and numbered label, gluing it in place where it will be visible through the bass-side sound-hole. All my instruments are individually hand-crafted, and each ends up a signed and numbered original, not a mass-produced instrument. I’m really not interested in doing things the “factory” way.
Installing the Back Plate
I used to complete all the work on the back plate, including purfling and final edge-work before installing it on the garland. But I have recently altered my order of operations so that I purfle and do edgework after the plate is installed. This allows me to adjust the plate overhang boundaries, and make final decisions as to how I want things to look, before permanently locking the shape in place by installing the purfling.
I also used to “self-induce panic,” by spreading hot hide glue around the perimeter of the garland and plate, and then frantically trying to align the edges perfectly and adjust all the (25-30) spool-clamps, etc. before the glue gelled. That was a fool’s-errand, as the glue usually gels far more quickly than I could ever get everything clamped in place. The late Sam Compton shared how he applied the glue and allowed it to gel, then aligned everything at a leisurely pace, gently clamping everything in place. Afterward, he went around the perimeter with a hair-dryer, gradually warming the plates until the glue re-liquefied. Finally, he tightened the clamps just enough to completely close the joints. Pretty clever.
I ended up clamping everything dry, then loosening a few clamps at a time, and slipping the hot hide-glue into the seams, using a very thin palette knife. That seems to work pretty well, and definitely eliminates stress. (His method probably is even better, but this is how I do things, for now.)
Final Edge Shape and Purfling
Once the back is securely glued in place, I can trim the edges to exactly the shape I want, so that the overhang is matching the front plate, etc., and then begin purfling.
I use the purfling marker to scribe in the double lines (except for the corners) where the purfling will be inlaid. I then draw in the corners very carefully. I have occasionally used a template for the corners, but it seems to not always work, since the corners are not always exactly the same. So I end up just making some layout marks to get the limits delineated, and then I draw the corners in, freehand.
I incise the purfling slot with a small, sharp knife, in three or more steps:
- The first pass with the knife is very shallow and light, only serving to deepen all the scribe marks.
- The second and third passes bring the purfling slot to the correct depth, and
- The last step is to use a purfling pick to remove all the waste wood between the paired cuts.
I check the depth and width of the slot by inserting a small section of purfling into the slot, all the way around, until I am sure that the slot is correct. then I bend and fit the purfling strips, and make sure the fit is as exact as I can make it, terminating in the classic “bee-stings” at the corners, rather than a simple “mitered corner.”
Finally, when all is as close to perfect as I can manage, I lift each section of purfling partially out of the slot, one at a time, and slip hot, thin, hide glue into the slot, using the thin palette knife again. I press the purfling all the way down to the bottom of the slot, and allow the glue to dry before beginning the final edgework.
The Channel, and Final Edgework:
I scribe a margin around the entire outer edge, usually about 1.6mm in from the outer edge. This will serve as the “limit” for the channel. I cut the channel using gouges first,then scrapers, and bringing the smooth curve up to match the scribed limit. Then I file the outer edge to round in from the center of the edge of the plate up to meet the scribed margin. I true up lines using scrapers, files, and abrasives, and then I am ready for final varnish preparations.
We’ll talk about all that in the next post, and post pictures. I need to get this one wrapped up. I’ll show close-ups of the edges and corners next time. there is still a long way to go, but it is looking more encouraging. 🙂
Thanks for looking.