Violin Progress

Please share with your friends!

Violin Progress

The Front Plate is Complete, except for the Bass Bar

This morning I got back to work on the scraping, and completed the outside of the front plate. The interior is also essentially complete, but still lacks the bass bar, so there is still that to do. I spent some time cleaning up the f-holes, and I am somewhat satisfied with them, but undoubtedly will do some tinkering later, just because I always do, and am never quite satisfied with them.

Front plate
Front plate

 

Back Plate Graduations have Begun

I knew I probably needed to get going on the neck, but I really wanted to begin the back plate graduations, so I started in. This is about as far as I got. I will probably complete it tomorrow, but my hands were getting tired, and I needed to do something easier for a bit.

Back Plate Progress
Back Plate Progress

 

Neck Beginning

You may recall that the neck block had been delivered to me in a trapezoidal cross-section. This is quite common, but it poses a problem for me, because, once I have the side profile of the scroll and pegbox laid out, I prefer to drill a pilot hole for each peg, using my small drill-press, so that the holes are all perpendicular to the centerline of the scroll. That is hard to do, with a sharp angled shape. So, I set my bandsaw for 1/4″, and sawed off a triangular slab from each side of the big end of the trapezoid, reversed them, and glued those slabs back onto the sides, near the thinner end of the trapezoid. I checked with my little square, to make sure I had them at an appropriate location, then clamped them home. Once the glue dries, I will square up the block, lay out the neck, drill the holes, and get going on carving the neck. Those wedges will be completely removed, long before the neck is done.

Slabs removed and rotated up to square up the neck billet.
Slabs removed and rotated up, making it possible to square up the neck billet.

 

Slabs glued and clamped.
Slabs glued and clamped. When the glue is dry, I can square the billet, and proceed with neck layout.

 

A Break-time Treat

Ann and I decided to take a break and go for a walk, as Spring seems to have arrived early. As we neared home again, a pair of Bald Eagles passed by, flying low over our place, and landing in the trees at the front of the property, on the far corner. I had never before heard eagles “chatting” with one another. It was interesting hearing their clear, high-pitched chirps, and whistles, as they “talked” back and forth.

One of them almost immediately re-located to a thicker stand of trees across the road, but the other obligingly remained in sight, preening herself, until a passing hawk began diving at her, and she, too, moved into the thicker cover. I only had my cell-phone, but I did manage to get one photo.

Eagle in the distance.
Eagle in the distance.

 

Back to Work:

Squaring the Neck Billet

Once the glue was dry, I could square the billet, by sanding or planing off excess wood. Removing those slabs had left me with a few milimeters extra on the thickness, and much more on the depth, from front to back. So, since I had tried to plane it, but it tore out badly (as curly maple frequently does) I straightened the sides using the oscillating spindle-sander, and then laid out the neck details. I have made a new neck template, but it is just thin plastic. I will eventually make a light aluminum template which will be more durable. I first laid out one side, including the locations for the peg holes. Then I drilled the 1/8″ pilot holes for the pegs and cut the profile out on my small band-saw. After that, I was able to lay out the other side, and all the rest of the details; including the width of the heel, the width of the button, the width of the neck at the nut, and the taper of the pegbox into the actual scroll.

I forgot to take photos during that step (sorry) so all I can show you is the sawing procedure I used to remove the excess wood from the scroll:

Dcroll carving, first step.
I cut tangents to the curves, down to the scroll outlines from both sides.

 

Curve sections ready to remove.
Once I have cut sections all the way around, I can easily remove those sections and begin carving.

 

I will try to complete the back plate, the bass-bar, and the neck/scroll tomorrow. If I get that far, I will feel as though I am “on the home stretch,”, as the neck-set will then be the only difficult step left to do. We’ll see, though. There may be other priorities to pursue.

 

Thanks for looking.

 

If you found this post helpful, please share with your friends!